Dryer Taking Too Long to Dry? 7 Checks to Try Before You Call for Repair

Dryer taking too long to dry: close-up of a clothes dryer door
90%fixed on the 1st visit
90-dayparts & labour warranty
$0if we can’t fix it
7 days8am–8pm, same-day in most areas

Your dryer is taking too long to dry when a normal load needs more than one full cycle, or the towels come out warm but still damp. In most homes in Surrey, Langley and across the Lower Mainland, the cause is restricted airflow, which you can check safely in about fifteen minutes. If the airflow is fine, the problem is usually a heating or sensor part, and that’s a job for a technician.

This guide covers why dryers slow down, seven checks you can do yourself, and the signs that it’s time to book dryer repair in Surrey or anywhere else in our service area.

Why is my dryer taking so long to dry clothes?

A dryer takes too long to dry when hot, moist air can’t leave the drum fast enough or the dryer isn’t producing enough heat. The most common causes are a clogged lint screen, a crushed or blocked vent hose, a blocked outside vent, an overloaded drum, a worn heating element or a faulty moisture sensor.

Every dryer works the same way: it heats air, pushes it through your clothes and exhausts the moisture outside. If any part of that chain is weak, the water stays in the drum. Most slow-drying problems fall into four groups:

  • Restricted airflow: lint buildup in the screen, hose or wall duct, or a stuck outside flap.
  • Weak heat: a worn heating element, a failing cycling thermostat or a blown thermal fuse. On gas dryers, it may be the igniter or gas valve coils.
  • Sensor or control issues: a coated moisture sensor or a faulty control board that ends the cycle too early.
  • Mechanical wear: a slipping belt, worn drum rollers or a damaged blower wheel that cuts the airflow.

Safety first

Unplug the dryer before every check below. If you have a gas dryer and need to pull it away from the wall, close the gas shut-off valve first and move it gently so the gas line isn’t strained. Never open the cabinet, touch the wiring or work on the gas line yourself.

7 checks to try when your dryer isn’t drying clothes

  1. Clean the lint screen properly.
  2. Inspect the vent hose behind the dryer.
  3. Check the outside vent flap.
  4. Load the drum correctly.
  5. Clean the moisture sensor bars.
  6. Compare a timed cycle with an auto-dry cycle.
  7. Check the breaker on an electric dryer.

1. Clean the lint screen properly

Remove the lint after every load. Once a month, run the screen under the tap: if water pools on top instead of passing through, fabric-softener residue has coated the mesh. Scrub it gently with warm, soapy water and a soft brush, then let it dry fully before you put it back.

2. Inspect the vent hose behind the dryer

Slide the dryer out and look at the hose that runs to the wall. It should be as short and straight as possible, with no kinks, crushed sections or sags where lint can settle. Thin plastic or foil hoses crush easily and trap lint, so a rigid or semi-rigid metal duct is the better choice. Disconnect the hose and check inside for buildup.

3. Check the outside vent flap

With everything reconnected, run the dryer on heat and go outside. You should feel a strong stream of warm air, and the flap should open fully. A weak puff or a flap that barely moves means the wall duct is likely blocked by lint, a bird’s nest or a damaged cap. Our article on the signs your dryer vent needs to be cleaned explains what to look for.

4. Load the drum correctly

Clothes need room to tumble so the hot air can reach them. An overpacked drum traps moisture, and very small loads can ball up and stay damp. Fill the drum about three-quarters full, shake items out before loading, and dry heavy towels separately from light shirts.

5. Clean the moisture sensor bars

Most modern dryers have two metal strips inside the drum, usually just below the lint screen. They tell the dryer when clothes are dry. Dryer-sheet residue can coat them so they read “dry” too early. Wipe them with a cloth and a little rubbing alcohol.

6. Compare a timed cycle with an auto-dry cycle

Run a normal load on a timed, high-heat cycle. If it dries well on timed heat but not on the sensor or auto-dry setting, the sensor or control board is the likely cause. If the dryer never gets properly hot on any setting, the heating system needs a closer look.

7. Check the breaker on an electric dryer

Electric dryers run on a 240-volt double breaker. If one half trips, the drum can still spin while the heater gets no power, so the dryer runs but stays cool. Reset the breaker once. If it trips again, stop using the dryer and call a technician.

Is it dangerous if my dryer takes two cycles?

It can be. A blocked vent makes the dryer run hotter and longer, which wears out the heating element and thermal fuse and builds up lint near hot parts. Clogged vents are a common cause of dryer fires. Long drying times also waste electricity or gas: ENERGY STAR’s clothes dryer guide covers how airflow and settings affect energy use.

When to call a dryer repair technician

Stop troubleshooting and book a repair if you notice any of these:

  • The dryer spins but stays cool or only lukewarm, even with a clean vent.
  • You smell burning, see scorched lint, or the cabinet feels very hot to the touch.
  • The breaker trips again after a reset.
  • You hear squealing, thumping or grinding from the drum.
  • The dryer stops mid-cycle or won’t start at all.
  • You smell gas. Leave the home right away, don’t use switches or flames, and call FortisBC or 911 from outside.

Heating elements, thermal fuses, igniters and control boards involve live electrical or gas parts, so they aren’t DIY repairs. A technician can test each part and replace only what has actually failed. If you’d like to know how a visit works, read what happens after an appliance inspection. If your dryer has no heat at all, our guide to dryers that won’t heat goes into more detail.

Dryer repair in Surrey and the Lower Mainland

Starfix Appliance Repair fixes electric and gas dryers in homes across the Lower Mainland and Fraser Valley, including Surrey, Langley, Burnaby, Coquitlam, Maple Ridge, Abbotsford and Chilliwack. When you book, tell us the dryer’s brand, whether it’s gas or electric, and what you’ve already checked. It helps the technician come prepared.

Frequently asked questions

Why are my clothes still damp after a full dryer cycle?

The most common reason is restricted airflow from a clogged lint screen, vent hose or outside vent. If the airflow is strong, the heating element, a thermostat or the moisture sensor is the next suspect. Try the timed-cycle test above to narrow it down.

How long should a dryer take to dry a normal load?

A typical mixed load usually dries in about 40 to 60 minutes. Heavy items like towels and jeans take longer. If a normal load regularly needs a second cycle, something is limiting heat or airflow.

How often should I clean my dryer vent?

Clean the lint screen after every load. Have the vent hose and wall duct checked at least once a year, and sooner if drying times start creeping up or the outside flap stops opening fully.

Can I replace a dryer heating element myself?

We don’t recommend it. The element is wired into the dryer’s high-voltage circuit, and a failed element is often a sign of another problem, like a blocked vent or a faulty thermostat. A technician can find and fix the root cause so the new part doesn’t fail again.

Do you repair both gas and electric dryers?

Yes. Starfix repairs electric and gas dryers throughout our service area. Let us know which type you have when you book.

Book your dryer repair with Starfix

If your dryer is still taking too long to dry after these checks, let a technician take a look. Call 604-900-2105 or book online at Starfix.ca, and we’ll get your laundry back on schedule.

Need a technician?

Electric and gas appliances repaired across Metro Vancouver and the Fraser Valley, 7 days a week, 8am to 8pm.

Request a service callCall 604-900-2105

Areas That We Service

Map of Starfix appliance repair service areas across the Lower Mainland and Fraser Valley
Starfix Appliance Repair

Request A Service Call

or call 604-900-2105

We never spam, we hate it too.